Buy Premium Account:
http://extabit.com/register.jsp?aff=b7e0f77412427e77
http://turbobit.net/partner/?PHPSESUD=1E4BBAEAA0CA999982939DDB7AF0BBF7
Any OSx86 installation guide can seem daunting at first glance, especially when trying to remember cryptic terminal commands and sorting through volumes of misinformation on the web. This guide requires no coding, terminal work, or Mac experience of any kind. You will not need access to a Mac. In fact, it's easier and faster for me to install Snow Leopard with fully working components on my system than it is to install Windows 7. And more fun.
The
iBoot + MultiBeast method is designed and tested for any desktop or laptop running the latest line of Intel processors, the Core i3/i5/i7s. I have had reports of success with older machines as well including CoreDuo, Core2Duo, and even Pentium 4. However, AMD processors are not supported.
YOU WILL NEED
- A computer running an Intel Processor
- A blank CD and dvd
- A Mac OS X Snow Leopard Retail DVD
- SATA ports- not the white Gigabyte SATA ports.
- It's best to use an empty hard drive- you will have to partition and format the drive.
- Always back up any of your important data.
BEFORE YOU BEGIN
- If you have greater than 4gb of RAM, remove the extra RAM for a maximum of 4gb. You can put back any extra RAM in after the installation process.
- Use only 1 graphics card in the 1st PCIe slot with 1 monitor plugged in.
- Remove any hard drives besides the blank drive being used for OS X.
- Remove any USB peripherals besides keyboard and mouse.
- Remove any PCI cards besides graphics- they may not be Mac compatible.
In order to boot the Mac OS X Retail DVD, you'll need iBoot For desktops and laptops using unsupported Intel CPUs and graphics, a legacy version of iBoot.
- Burn iBoot the image to CD
- Place iBoot in CD/DVD drive
- Restart computer
- At boot prompt, eject iBoot
- Insert your Mac OS X Snow Leopard 10.6.3 Retail DVD and press F5
- When you see the screen below, press enter to begin the boot process
- When you get to the installation screen, open Utilities/Disk Utility. NOTE: If you cannot get to the installation screen, retry from Step 4, type PCIRootUID=1 before hitting enter. If that doesn't work then try PCIRootUID=1 -x or just -x which will enter Mac OS X Safe Mode and will allow you to proceed. For some graphics cards, use GraphicsEnabler=No boot flag to proceed.
- Partition your hard drive to GUID Partition Table
- Format your hard drive to Mac OS Extended (Journaled). NOTE: The bootloader can only boot from a disk or partition of 1 TB or less. Partition larger drives.
- For the purposes of this guide, name it Snow Leopard. You can rename it later.
- Close Disk Utility
- When the installer asks you where to install, choose Snow Leopard
- Choose Customize‚ and uncheck additional options. This will hasten the install process. You can always install this stuff later.
- Restart computer.
- Place iBoot back in drive.
- When you get to the boot selection screen, choose your new Snow Leopard installation.
· For Sandy Bridge system you need update helper before updating 10.6.8 the update helper folder is inside the folder you have downloaded. Installe update helper >>>> reboot >>> Run 10.6.8 combo update >>> reboot
For other PC without sandy bridge please follow these steps :
- Open Finder and navigate to your Snow Leopard drive.
- Ope the mac os x combo update.dmg
- Open MultiBeast- don't run it yet, just leave it open. Set up windows as shown.
- Mount MacOSXUpdCombo10.6.8.dmg
- Install MacOSXUpdCombo10.6.8.pkg
- Upon completion, the installer will ask you to reboot. DO NOT REBOOT.
- Switch to the already open MultiBeast. If it closes, just re-open it.
MultiBeast is an all-in-one post-installation tool designed to enable boot from hard drive, and install support for Audio, Network, and Graphics. It contains two different complete post-installation solutions: EasyBeast and UserDSDT. In addition it includes System Utilities to rebuild caches and repair permissions and a collection of drivers, boot loaders, boot time config files and handy software.
Choose one of the following options directly following a fresh installation and update:
EasyBeast is a DSDT-free solution for any Core/Core2/Core i system. It installs all of the essentials to allow your system to boot from the hard drive. Audio, Graphics and Network will have to be enabled separately.
UserDSDT is a bare-minimum solution for those who have their own pre-edited DSDT. Place your DSDT.aml on the desktop before install. Audio, Graphics and Network will have to be enabled separately. HINT: Check the DSDT Database for a pre-edited DSDT.
- Run MultiBeast.
- If you have a custom DSDT that's been edited, place the file on your desktop and chooseUserDSDT.
- All others select EasyBeast
- Select System Utilities.
- Optionally, you may install further drivers via Advanced Options to enable ethernet, sound, graphics, etc... Be sure to read the documentation provided about each installation option. NOTE: EasyBeast, and UserDSDT install the bootloader by default, so you'll not need to check that option.
- Install to Snow Leopard- it should take about 4 minutes to run scripts.
- Eject iBoot.
- Reboot- from your new Snow Leopard installation drive.
Congratulations! You're done!!
Your PC is now fully operational, while running the latest version of Mac OS X Snow Leopard! And you have a nice Boot CD to get into your system in case things go awry. Boot your system from iBoot if you have issues. You may run MultiBeast as often as you like.
If you can't boot, try typing -x at the boot prompt to enter safe mode, or just boot with iBoot. When you get to the desktop, you can make all of the changes you need to. The best way to start fresh is delete whatever you're trying to get rid of- including the whole /Extra folder, as most kexts are installed there. Then you can re-run MultiBeast. As long as you rebuild caches and repair permissions after you're done, you can do just about anything you want to /Extra/Extensions and /System/Library/Extensions. Anything can be tweaked and enabled upon subsequent uses of MultiBeast.
==============================================================
This DVD is retail version of Mac OS X Lion 10.7.2 just burn it to a DVD and start installing Mac OS X Lion 10.7.2 to your Mac and for people with Hackintosh PCs you can use this to make your own bootable Mac OS X DVD using regae method or unibeast.
==============================================================
· If you're facing hangs, freezes or kernel panics (which is present as a shutdown symbol on the screen just after boot) type in "-v" (without quotes) in the boot command of the bootloader. This would give you verbose output which means you will see where the problem is.
· If you are stuck at “PCI configuration begin -v npci=0×2000” in boot command of the bootloader use this command :
· "Waiting for root device" - It means that OS X doesn't see your hard disk or boot device. You can face with this during dvd boot or after system install during hdd boot.
· White or black screen during HDD boot - This means that OS X doesn't see your monitor properly or your graphics card isn't working correctly. Use : GraphicsEnabler=No
· Keep in mind that sometimes certain kext patches may not work for your system even though they are the same chipset but a slight variation may cause it not to work on your PC. The result may be a kernel panic again, reinstall back but this time don't select any funny patches/drivers. This would resolve your problem.
- if you happen to forget and say installed windows in IDE instead of sata=AHCI don't worry it happened to me before. windows won't start so go to bios and Sata=Disable and then restart
simply go to Start on windows type:
REGEDIT
go to windows local machine -->System....>CurrentControlSet........>Services....>MsAHCI
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ MSAHCI and on the right pane change the value of the string to 0 save and you should be ok to go back to bios and re-enable AHCI
==========================================================================
Buy Premium Account:
http://extabit.com/register.jsp?aff=b7e0f77412427e77
http://turbobit.net/partner/?PHPSESUD=1E4BBAEAA0CA999982939DDB7AF0BBF7
All the files are included in the final version of this guide which is when you download the Mahmood1_MacOSX_Lion_10.7.2_iAKTOS or download it from my site only the files for post-installation. After you have installed Mac OS X Lion or Snow Leopard on your PC now if you have problems with graphic cards, sound, network you can apply tweaks that can solve these problems. To enable graphics to its full 100% potential you must use the right kext to install and also the right DSDT.aml file.
The steps that can be taken or files that are needed after installing Mac OS X on PC :
1. Kext installer app (use KextBeast)
3. OSX86 installer (use OSX86Tools_1.0.150)
4. To install all drivers using Multibeast use (MultiBeast-4.2.1_MacOSX_Lion if you are using snow leopard use MultiBeast 3.10.1: Snow Leopard Edition)
5. If something goes wrong and you cant boot use (rescueCD_rBoot just burn it to a CD and that’s it)
6. Install the kexts PCI config begin if u r getting error of PCI configuration begin or in bootloader use this command : npci=0x2000
========================================================
How to dual boot Windows OS and Mac OS X on hackintosh :
Download EasyBCD and instructions from here :
if you have used the Install Mac OS X Lion 10.7.2 using a Mahmood1_MacOSX_Lion_10.7.2_iAKTOS DVD then you don't need anything else when you are at boot screen just boot to the drive you want by using arrow keys to go left and right of the screen boot options.
Step 1 : you came here because you have installed Mac OS X on your PC !! and now you want dual boot am i correct so go to step 2 !!
Step 2 : Reactivate Windows Partition
· Now you shall be able to boot into mac, but not your windows. Don't worry as u can reactivate it, provided you have your windows installation DVD (Vista/7). Original
· Boot into your Windows DVD.
· Click Repair your computer.
· Click the operating system that you want to repair, and then click Next.
· In the System Recovery Options dialog box, click Command Prompt.
· Type DISKPART and hit ENTER
· type "list disk" and hit ENTER.
· lets say yur hard disk is Disk 0, type "select disk 0" and hit enter
· type "list partition" and hit ENTER
· see which partition is your Windows System Partition "C" drive. usually it's partition 2.
· type "select partition 2" and hit ENTER...(if yours is really partition 2)
· type "active" and hit ENTER.
· type "exit" and hit ENTER
restart your computer. now you shall be able to boot into windows but not your mac. Don't worry, the next step going to be the final, crucial yet easy one...
STEP 3:EASY BCD (dual boot essential part !!)
Once you've boot into windows, download and install EASY BCD here
Run EASY BCD, click ADD NEW ENTRY
Select Mac TAB, choose MBR mode as below.
Close EASYBCD and restart. Restart and now you can see both windows and mac in Windows Boot Manager.
=========================================================
Thanks to all people who have provided us with all information and guide and dvd to make this possible.
iAktos for mac os x lion dvd, insanleymac forum, osx86 for kext files and tonymac for great softwares !!
Buy Premium Account:
